# Tutorial 06 - UART Chainloader ## tl;dr - Running from an SD card was a nice experience, but it would be extremely tedious to do it for every new binary. So let's write a [chainloader]. - This will be the last binary you need to put on the SD card. Each following tutorial will provide a `chainboot` target in the `Makefile` that lets you conveniently load the kernel over `UART`. [chainloader]: https://en.wikipedia.org/wiki/Chain_loading ## Note Please note that there is stuff going on in this tutorial that is very hard to grasp by only looking at the source code changes. The gist of it is that in `boot.s`, we are writing a piece of [position independent code] which automatically determines where the firmware has loaded the binary (`0x8_0000`), and where it was linked to (`0x200_0000`, see `link.ld`). The binary then copies itself from loaded to linked address (aka "relocating" itself), and then jumps to the relocated version of `_start_rust()`. Since the chainloader has put itself "out of the way" now, it can now receive another kernel binary from the `UART` and copy it to the standard load address of the RPi firmware at `0x8_0000`. Finally, it jumps to `0x8_0000` and the newly loaded binary transparently executes as if it had been loaded from SD card all along. Please bear with me until I find the time to write it all down here elaborately. For the time being, please see this tutorial as an enabler for a convenience feature that allows booting the following tutorials in a quick manner. [position independent code]: https://en.wikipedia.org/wiki/Position-independent_code ## Install and test it Our chainloader is called `MiniLoad` and is inspired by [raspbootin]. You can try it with this tutorial already: 1. Depending on your target hardware, run:`make` or `BSP=rpi4 make`. 1. Copy `kernel8.img` to the SD card and put the SD card back into your RPi. 1. Run `make chainboot` or `BSP=rpi4 make chainboot`. 1. Connect the USB serial to your host PC. - Wiring diagram at [top-level README](../README.md#-usb-serial-output). - Make sure that you **DID NOT** connect the power pin of the USB serial. Only RX/TX and GND. 1. Connect the RPi to the (USB) power cable. 1. Observe the loader fetching a kernel over `UART`: > ❗ **NOTE**: `make chainboot` assumes a default serial device name of `/dev/ttyUSB0`. Depending on > your host operating system, the device name might differ. For example, on `macOS`, it might be > something like `/dev/tty.usbserial-0001`. In this case, please give the name explicitly: ```console $ DEV_SERIAL=/dev/tty.usbserial-0001 make chainboot ``` [raspbootin]: https://github.com/mrvn/raspbootin ```console $ make chainboot [...] Minipush 1.0 [MP] ⏳ Waiting for /dev/ttyUSB0 [MP] ✅ Serial connected [MP] 🔌 Please power the target now __ __ _ _ _ _ | \/ (_)_ _ (_) | ___ __ _ __| | | |\/| | | ' \| | |__/ _ \/ _` / _` | |_| |_|_|_||_|_|____\___/\__,_\__,_| Raspberry Pi 3 [ML] Requesting binary [MP] ⏩ Pushing 6 KiB ==========================================🦀 100% 0 KiB/s Time: 00:00:00 [ML] Loaded! Executing the payload now [0] mingo version 0.5.0 [1] Booting on: Raspberry Pi 3 [2] Drivers loaded: 1. BCM GPIO 2. BCM PL011 UART [3] Chars written: 117 [4] Echoing input now ``` In this tutorial, a version of the kernel from the previous tutorial is loaded for demo purposes. In subsequent tutorials, it will be the working directory's kernel. ## Test it The `Makefile` in this tutorial has an additional target, `qemuasm`, that lets you nicely observe how the kernel, after relocating itself, jumps the load address region (`0x80_XXX`) to the relocated code at (`0x0200_0XXX`): ```console $ make qemuasm [...] N: 0x00080030: 58000140 ldr x0, #0x80058 0x00080034: 9100001f mov sp, x0 0x00080038: 58000141 ldr x1, #0x80060 0x0008003c: d61f0020 br x1 ---------------- IN: 0x02000070: 9400044c bl #0x20011a0 ---------------- IN: 0x020011a0: 90000008 adrp x8, #0x2001000 0x020011a4: 90000009 adrp x9, #0x2001000 0x020011a8: f9446508 ldr x8, [x8, #0x8c8] 0x020011ac: f9446929 ldr x9, [x9, #0x8d0] 0x020011b0: eb08013f cmp x9, x8 0x020011b4: 54000109 b.ls #0x20011d4 [...] ``` ## Diff to previous ```diff diff -uNr 05_drivers_gpio_uart/Cargo.toml 06_uart_chainloader/Cargo.toml --- 05_drivers_gpio_uart/Cargo.toml +++ 06_uart_chainloader/Cargo.toml @@ -1,6 +1,6 @@ [package] name = "mingo" -version = "0.5.0" +version = "0.6.0" authors = ["Andre Richter "] edition = "2018" Binary files 05_drivers_gpio_uart/demo_payload_rpi3.img and 06_uart_chainloader/demo_payload_rpi3.img differ Binary files 05_drivers_gpio_uart/demo_payload_rpi4.img and 06_uart_chainloader/demo_payload_rpi4.img differ diff -uNr 05_drivers_gpio_uart/Makefile 06_uart_chainloader/Makefile --- 05_drivers_gpio_uart/Makefile +++ 06_uart_chainloader/Makefile @@ -22,27 +22,29 @@ # BSP-specific arguments. ifeq ($(BSP),rpi3) - TARGET = aarch64-unknown-none-softfloat - KERNEL_BIN = kernel8.img - QEMU_BINARY = qemu-system-aarch64 - QEMU_MACHINE_TYPE = raspi3 - QEMU_RELEASE_ARGS = -serial stdio -display none - OBJDUMP_BINARY = aarch64-none-elf-objdump - NM_BINARY = aarch64-none-elf-nm - READELF_BINARY = aarch64-none-elf-readelf - LINKER_FILE = src/bsp/raspberrypi/link.ld - RUSTC_MISC_ARGS = -C target-cpu=cortex-a53 + TARGET = aarch64-unknown-none-softfloat + KERNEL_BIN = kernel8.img + QEMU_BINARY = qemu-system-aarch64 + QEMU_MACHINE_TYPE = raspi3 + QEMU_RELEASE_ARGS = -serial stdio -display none + OBJDUMP_BINARY = aarch64-none-elf-objdump + NM_BINARY = aarch64-none-elf-nm + READELF_BINARY = aarch64-none-elf-readelf + LINKER_FILE = src/bsp/raspberrypi/link.ld + RUSTC_MISC_ARGS = -C target-cpu=cortex-a53 + CHAINBOOT_DEMO_PAYLOAD = demo_payload_rpi3.img else ifeq ($(BSP),rpi4) - TARGET = aarch64-unknown-none-softfloat - KERNEL_BIN = kernel8.img - QEMU_BINARY = qemu-system-aarch64 - QEMU_MACHINE_TYPE = - QEMU_RELEASE_ARGS = -serial stdio -display none - OBJDUMP_BINARY = aarch64-none-elf-objdump - NM_BINARY = aarch64-none-elf-nm - READELF_BINARY = aarch64-none-elf-readelf - LINKER_FILE = src/bsp/raspberrypi/link.ld - RUSTC_MISC_ARGS = -C target-cpu=cortex-a72 + TARGET = aarch64-unknown-none-softfloat + KERNEL_BIN = kernel8.img + QEMU_BINARY = qemu-system-aarch64 + QEMU_MACHINE_TYPE = + QEMU_RELEASE_ARGS = -serial stdio -display none + OBJDUMP_BINARY = aarch64-none-elf-objdump + NM_BINARY = aarch64-none-elf-nm + READELF_BINARY = aarch64-none-elf-readelf + LINKER_FILE = src/bsp/raspberrypi/link.ld + RUSTC_MISC_ARGS = -C target-cpu=cortex-a72 + CHAINBOOT_DEMO_PAYLOAD = demo_payload_rpi4.img endif QEMU_MISSING_STRING = "This board is not yet supported for QEMU." @@ -74,8 +76,8 @@ -O binary EXEC_QEMU = $(QEMU_BINARY) -M $(QEMU_MACHINE_TYPE) -EXEC_TEST_DISPATCH = ruby ../common/tests/dispatch.rb -EXEC_MINITERM = ruby ../common/serial/miniterm.rb +EXEC_TEST_MINIPUSH = ruby tests/chainboot_test.rb +EXEC_MINIPUSH = ruby ../common/serial/minipush.rb ##------------------------------------------------------------------------------ ## Dockerization @@ -94,7 +96,7 @@ ifeq ($(shell uname -s),Linux) DOCKER_CMD_DEV = $(DOCKER_CMD_INTERACT) $(DOCKER_ARG_DEV) - DOCKER_MINITERM = $(DOCKER_CMD_DEV) $(DOCKER_ARG_DIR_COMMON) $(DOCKER_IMAGE) + DOCKER_CHAINBOOT = $(DOCKER_CMD_DEV) $(DOCKER_ARG_DIR_COMMON) $(DOCKER_IMAGE) endif @@ -102,7 +104,7 @@ ##-------------------------------------------------------------------------------------------------- ## Targets ##-------------------------------------------------------------------------------------------------- -.PHONY: all $(KERNEL_ELF) $(KERNEL_BIN) doc qemu miniterm clippy clean readelf objdump nm check +.PHONY: all $(KERNEL_ELF) $(KERNEL_BIN) doc qemu chainboot clippy clean readelf objdump nm check all: $(KERNEL_BIN) @@ -131,7 +133,7 @@ ##------------------------------------------------------------------------------ ifeq ($(QEMU_MACHINE_TYPE),) # QEMU is not supported for the board. -qemu: +qemu qemuasm: $(call colorecho, "\n$(QEMU_MISSING_STRING)") else # QEMU is supported. @@ -139,13 +141,18 @@ qemu: $(KERNEL_BIN) $(call colorecho, "\nLaunching QEMU") @$(DOCKER_QEMU) $(EXEC_QEMU) $(QEMU_RELEASE_ARGS) -kernel $(KERNEL_BIN) + +qemuasm: $(KERNEL_BIN) + $(call colorecho, "\nLaunching QEMU with ASM output") + @$(DOCKER_QEMU) $(EXEC_QEMU) $(QEMU_RELEASE_ARGS) -kernel $(KERNEL_BIN) -d in_asm + endif ##------------------------------------------------------------------------------ -## Connect to the target's serial +## Push the kernel to the real HW target ##------------------------------------------------------------------------------ -miniterm: - @$(DOCKER_MINITERM) $(EXEC_MINITERM) $(DEV_SERIAL) +chainboot: $(KERNEL_BIN) + @$(DOCKER_CHAINBOOT) $(EXEC_MINIPUSH) $(DEV_SERIAL) $(CHAINBOOT_DEMO_PAYLOAD) ##------------------------------------------------------------------------------ ## Run clippy @@ -209,7 +216,8 @@ ##------------------------------------------------------------------------------ test_boot: $(KERNEL_BIN) $(call colorecho, "\nBoot test - $(BSP)") - @$(DOCKER_TEST) $(EXEC_TEST_DISPATCH) $(EXEC_QEMU) $(QEMU_RELEASE_ARGS) -kernel $(KERNEL_BIN) + @$(DOCKER_TEST) $(EXEC_TEST_MINIPUSH) $(EXEC_QEMU) $(QEMU_RELEASE_ARGS) \ + -kernel $(KERNEL_BIN) $(CHAINBOOT_DEMO_PAYLOAD) test: test_boot diff -uNr 05_drivers_gpio_uart/src/_arch/aarch64/cpu/boot.s 06_uart_chainloader/src/_arch/aarch64/cpu/boot.s --- 05_drivers_gpio_uart/src/_arch/aarch64/cpu/boot.s +++ 06_uart_chainloader/src/_arch/aarch64/cpu/boot.s @@ -18,6 +18,17 @@ add \register, \register, #:lo12:\symbol .endm +// Load the address of a symbol into a register, absolute. +// +// # Resources +// +// - https://sourceware.org/binutils/docs-2.36/as/AArch64_002dRelocations.html +.macro ADR_ABS register, symbol + movz \register, #:abs_g2:\symbol + movk \register, #:abs_g1_nc:\symbol + movk \register, #:abs_g0_nc:\symbol +.endm + .equ _core_id_mask, 0b11 //-------------------------------------------------------------------------------------------------- @@ -39,23 +50,35 @@ // If execution reaches here, it is the boot core. // Initialize DRAM. - ADR_REL x0, __bss_start - ADR_REL x1, __bss_end_exclusive + ADR_ABS x0, __bss_start + ADR_ABS x1, __bss_end_exclusive .L_bss_init_loop: cmp x0, x1 - b.eq .L_prepare_rust + b.eq .L_relocate_binary stp xzr, xzr, [x0], #16 b .L_bss_init_loop + // Next, relocate the binary. +.L_relocate_binary: + ADR_REL x0, __binary_nonzero_start // The address the binary got loaded to. + ADR_ABS x1, __binary_nonzero_start // The address the binary was linked to. + ADR_ABS x2, __binary_nonzero_end_exclusive + +.L_copy_loop: + ldr x3, [x0], #8 + str x3, [x1], #8 + cmp x1, x2 + b.lo .L_copy_loop + // Prepare the jump to Rust code. -.L_prepare_rust: // Set the stack pointer. - ADR_REL x0, __boot_core_stack_end_exclusive + ADR_ABS x0, __boot_core_stack_end_exclusive mov sp, x0 - // Jump to Rust code. - b _start_rust + // Jump to the relocated Rust code. + ADR_ABS x1, _start_rust + br x1 // Infinitely wait for events (aka "park the core"). .L_parking_loop: diff -uNr 05_drivers_gpio_uart/src/bsp/device_driver/bcm/bcm2xxx_gpio.rs 06_uart_chainloader/src/bsp/device_driver/bcm/bcm2xxx_gpio.rs --- 05_drivers_gpio_uart/src/bsp/device_driver/bcm/bcm2xxx_gpio.rs +++ 06_uart_chainloader/src/bsp/device_driver/bcm/bcm2xxx_gpio.rs @@ -148,7 +148,7 @@ // Make an educated guess for a good delay value (Sequence described in the BCM2837 // peripherals PDF). // - // - According to Wikipedia, the fastest Pi3 clocks around 1.4 GHz. + // - According to Wikipedia, the fastest RPi4 clocks around 1.5 GHz. // - The Linux 2837 GPIO driver waits 1 µs between the steps. // // So lets try to be on the safe side and default to 2000 cycles, which would equal 1 µs diff -uNr 05_drivers_gpio_uart/src/bsp/device_driver/bcm/bcm2xxx_pl011_uart.rs 06_uart_chainloader/src/bsp/device_driver/bcm/bcm2xxx_pl011_uart.rs --- 05_drivers_gpio_uart/src/bsp/device_driver/bcm/bcm2xxx_pl011_uart.rs +++ 06_uart_chainloader/src/bsp/device_driver/bcm/bcm2xxx_pl011_uart.rs @@ -284,7 +284,7 @@ } /// Retrieve a character. - fn read_char_converting(&mut self, blocking_mode: BlockingMode) -> Option { + fn read_char(&mut self, blocking_mode: BlockingMode) -> Option { // If RX FIFO is empty, if self.registers.FR.matches_all(FR::RXFE::SET) { // immediately return in non-blocking mode. @@ -299,12 +299,7 @@ } // Read one character. - let mut ret = self.registers.DR.get() as u8 as char; - - // Convert carrige return to newline. - if ret == '\r' { - ret = '\n' - } + let ret = self.registers.DR.get() as u8 as char; // Update statistics. self.chars_read += 1; @@ -384,14 +379,14 @@ impl console::interface::Read for PL011Uart { fn read_char(&self) -> char { self.inner - .lock(|inner| inner.read_char_converting(BlockingMode::Blocking).unwrap()) + .lock(|inner| inner.read_char(BlockingMode::Blocking).unwrap()) } fn clear_rx(&self) { // Read from the RX FIFO until it is indicating empty. while self .inner - .lock(|inner| inner.read_char_converting(BlockingMode::NonBlocking)) + .lock(|inner| inner.read_char(BlockingMode::NonBlocking)) .is_some() {} } diff -uNr 05_drivers_gpio_uart/src/bsp/raspberrypi/link.ld 06_uart_chainloader/src/bsp/raspberrypi/link.ld --- 05_drivers_gpio_uart/src/bsp/raspberrypi/link.ld +++ 06_uart_chainloader/src/bsp/raspberrypi/link.ld @@ -16,7 +16,8 @@ SECTIONS { - . = __rpi_load_addr; + /* Set the link address to 32 MiB */ + . = 0x2000000; /* ^ */ /* | stack */ /* | growth */ @@ -26,6 +27,7 @@ /*********************************************************************************************** * Code + RO Data + Global Offset Table ***********************************************************************************************/ + __binary_nonzero_start = .; .text : { KEEP(*(.text._start)) @@ -42,6 +44,10 @@ ***********************************************************************************************/ .data : { *(.data*) } :segment_rw + /* Fill up to 8 byte, b/c relocating the binary is done in u64 chunks */ + . = ALIGN(8); + __binary_nonzero_end_exclusive = .; + /* Section is zeroed in pairs of u64. Align start and end to 16 bytes */ .bss : ALIGN(16) { diff -uNr 05_drivers_gpio_uart/src/bsp/raspberrypi/memory.rs 06_uart_chainloader/src/bsp/raspberrypi/memory.rs --- 05_drivers_gpio_uart/src/bsp/raspberrypi/memory.rs +++ 06_uart_chainloader/src/bsp/raspberrypi/memory.rs @@ -11,9 +11,10 @@ /// The board's physical memory map. #[rustfmt::skip] pub(super) mod map { + pub const BOARD_DEFAULT_LOAD_ADDRESS: usize = 0x8_0000; - pub const GPIO_OFFSET: usize = 0x0020_0000; - pub const UART_OFFSET: usize = 0x0020_1000; + pub const GPIO_OFFSET: usize = 0x0020_0000; + pub const UART_OFFSET: usize = 0x0020_1000; /// Physical devices. #[cfg(feature = "bsp_rpi3")] @@ -35,3 +36,13 @@ pub const PL011_UART_START: usize = START + UART_OFFSET; } } + +//-------------------------------------------------------------------------------------------------- +// Public Code +//-------------------------------------------------------------------------------------------------- + +/// The address on which the Raspberry firmware loads every binary by default. +#[inline(always)] +pub fn board_default_load_addr() -> *const u64 { + map::BOARD_DEFAULT_LOAD_ADDRESS as _ +} diff -uNr 05_drivers_gpio_uart/src/main.rs 06_uart_chainloader/src/main.rs --- 05_drivers_gpio_uart/src/main.rs +++ 06_uart_chainloader/src/main.rs @@ -105,6 +105,7 @@ //! 2. Once finished with architectural setup, the arch code calls `kernel_init()`. #![allow(clippy::upper_case_acronyms)] +#![feature(asm)] #![feature(const_fn_fn_ptr_basics)] #![feature(format_args_nl)] #![feature(global_asm)] @@ -142,38 +143,56 @@ kernel_main() } +const MINILOAD_LOGO: &str = r#" + __ __ _ _ _ _ +| \/ (_)_ _ (_) | ___ __ _ __| | +| |\/| | | ' \| | |__/ _ \/ _` / _` | +|_| |_|_|_||_|_|____\___/\__,_\__,_| +"#; + /// The main function running after the early init. fn kernel_main() -> ! { use bsp::console::console; use console::interface::All; - use driver::interface::DriverManager; - - println!( - "[0] {} version {}", - env!("CARGO_PKG_NAME"), - env!("CARGO_PKG_VERSION") - ); - println!("[1] Booting on: {}", bsp::board_name()); - - println!("[2] Drivers loaded:"); - for (i, driver) in bsp::driver::driver_manager() - .all_device_drivers() - .iter() - .enumerate() - { - println!(" {}. {}", i + 1, driver.compatible()); - } - println!( - "[3] Chars written: {}", - bsp::console::console().chars_written() - ); - println!("[4] Echoing input now"); + println!("{}", MINILOAD_LOGO); + println!("{:^37}", bsp::board_name()); + println!(); + println!("[ML] Requesting binary"); + console().flush(); - // Discard any spurious received characters before going into echo mode. + // Discard any spurious received characters before starting with the loader protocol. console().clear_rx(); - loop { - let c = bsp::console::console().read_char(); - bsp::console::console().write_char(c); + + // Notify `Minipush` to send the binary. + for _ in 0..3 { + console().write_char(3 as char); } + + // Read the binary's size. + let mut size: u32 = u32::from(console().read_char() as u8); + size |= u32::from(console().read_char() as u8) << 8; + size |= u32::from(console().read_char() as u8) << 16; + size |= u32::from(console().read_char() as u8) << 24; + + // Trust it's not too big. + console().write_char('O'); + console().write_char('K'); + + let kernel_addr: *mut u8 = bsp::memory::board_default_load_addr() as *mut u8; + unsafe { + // Read the kernel byte by byte. + for i in 0..size { + core::ptr::write_volatile(kernel_addr.offset(i as isize), console().read_char() as u8) + } + } + + println!("[ML] Loaded! Executing the payload now\n"); + console().flush(); + + // Use black magic to create a function pointer. + let kernel: fn() -> ! = unsafe { core::mem::transmute(kernel_addr) }; + + // Jump to loaded kernel! + kernel() } diff -uNr 05_drivers_gpio_uart/tests/boot_test_string.rb 06_uart_chainloader/tests/boot_test_string.rb --- 05_drivers_gpio_uart/tests/boot_test_string.rb +++ 06_uart_chainloader/tests/boot_test_string.rb @@ -1,3 +0,0 @@ -# frozen_string_literal: true - -EXPECTED_PRINT = 'Echoing input now' diff -uNr 05_drivers_gpio_uart/tests/chainboot_test.rb 06_uart_chainloader/tests/chainboot_test.rb --- 05_drivers_gpio_uart/tests/chainboot_test.rb +++ 06_uart_chainloader/tests/chainboot_test.rb @@ -0,0 +1,80 @@ +# frozen_string_literal: true + +# SPDX-License-Identifier: MIT OR Apache-2.0 +# +# Copyright (c) 2020-2021 Andre Richter + +require_relative '../../common/serial/minipush' +require_relative '../../common/tests/boot_test' +require 'pty' + +# Match for the last print that 'demo_payload_rpiX.img' produces. +EXPECTED_PRINT = 'Echoing input now' + +# Extend BootTest so that it listens on the output of a MiniPush instance, which is itself connected +# to a QEMU instance instead of a real HW. +class ChainbootTest < BootTest + MINIPUSH = '../common/serial/minipush.rb' + MINIPUSH_POWER_TARGET_REQUEST = 'Please power the target now' + + def initialize(qemu_cmd, payload_path) + super(qemu_cmd, EXPECTED_PRINT) + + @test_name = 'Boot test using Minipush' + + @payload_path = payload_path + end + + private + + # override + def post_process_and_add_output(output) + temp = output.join.split("\r\n") + + # Should a line have solo carriage returns, remove any overridden parts of the string. + temp.map! { |x| x.gsub(/.*\r/, '') } + + @test_output += temp + end + + def wait_for_minipush_power_request(mp_out) + output = [] + Timeout.timeout(MAX_WAIT_SECS) do + loop do + output << mp_out.gets + break if output.last.include?(MINIPUSH_POWER_TARGET_REQUEST) + end + end + rescue Timeout::Error + @test_error = 'Timed out waiting for power request' + rescue StandardError => e + @test_error = e.message + ensure + post_process_and_add_output(output) + end + + # override + def setup + pty_main, pty_secondary = PTY.open + mp_out, _mp_in = PTY.spawn("ruby #{MINIPUSH} #{pty_secondary.path} #{@payload_path}") + + # Wait until MiniPush asks for powering the target. + wait_for_minipush_power_request(mp_out) + + # Now is the time to start QEMU with the chainloader binary. QEMU's virtual tty is connected + # to the MiniPush instance spawned above, so that the two processes talk to each other. + Process.spawn(@qemu_cmd, in: pty_main, out: pty_main) + + # The remainder of the test is done by the parent class' run_concrete_test, which listens on + # @qemu_serial. Hence, point it to MiniPush's output. + @qemu_serial = mp_out + end +end + +##-------------------------------------------------------------------------------------------------- +## Execution starts here +##-------------------------------------------------------------------------------------------------- +payload_path = ARGV.pop +qemu_cmd = ARGV.join(' ') + +ChainbootTest.new(qemu_cmd, payload_path).run diff -uNr 05_drivers_gpio_uart/update.sh 06_uart_chainloader/update.sh --- 05_drivers_gpio_uart/update.sh +++ 06_uart_chainloader/update.sh @@ -0,0 +1,8 @@ +#!/usr/bin/env bash + +cd ../05_drivers_gpio_uart +BSP=rpi4 make +cp kernel8.img ../06_uart_chainloader/demo_payload_rpi4.img +make +cp kernel8.img ../06_uart_chainloader/demo_payload_rpi3.img +rm kernel8.img ```