mirror of https://github.com/pikvm/pikvm
You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
175 lines
10 KiB
Markdown
175 lines
10 KiB
Markdown
# Hardware Arduino HID instead of the OTG
|
|
Using Arduino HID on non-v0 platforms is useful if you need a simple and primitive keyboard/mouse emulator device. For example when used with a hardware KVM switch which [does not recognize composite HID](https://github.com/pikvm/pikvm/issues/7). You can also use the Arduino HID to emulate the PS/2 keyboard.
|
|
|
|
- NOTE: AIMOS KVM switches do not work with the aruduino, please consider using an alternitive.
|
|
|
|
## USB keyboard & mouse
|
|
* Build and connect HID according to the [diagram](../README.md#setting-up-the-v0) (the bottom part with transistor, level-shifter and Arduino).
|
|
* Switch to RW-mode using command `rw`.
|
|
* Add these lines to `/etc/kvmd/override.yaml` (remove `{}` in the file before):
|
|
```yaml
|
|
kvmd:
|
|
hid:
|
|
type: serial
|
|
reset_pin: 4
|
|
device: /dev/kvmd-hid
|
|
```
|
|
* Create file `/etc/udev/rules.d/99-kvmd-extra.rules`:
|
|
```udev
|
|
KERNEL=="ttyAMA0", SYMLINK+="kvmd-hid"
|
|
```
|
|
* Run `systemctl disable getty@ttyAMA0.service`.
|
|
* Remove `console=ttyAMA0,115200`or `console=serial0,115200` and `kgdboc=ttyAMA0,115200` or `kgdboc=serial0,115200` from `/boot/cmdline.txt`.
|
|
* [Flash the Arduino HID](flashing_hid.md).
|
|
* Run `reboot`.
|
|
|
|
## PS/2 keyboard
|
|
Using the PS/2 firmware currently has the following limitations:
|
|
* The possibility of using the switchable USB HID is excluded.
|
|
* PS/2 mouse is not supported right now (but it will).
|
|
|
|
Both of these problems will be solved in the nearest future and the two different firmware versions will be combined into one universal one.
|
|
|
|
To select the PS/2 firmware, you need to follow the instructions for USB, but with one exception. Before `make` you need to edit file `platformio.ini`. Open it and find these lines:
|
|
```ini
|
|
[_common]
|
|
build_flags =
|
|
-DHID_PS2_KBD_CLOCK_PIN=7
|
|
-DHID_PS2_KBD_DATA_PIN=5
|
|
-DHID_USB_CHECK_ENDPOINT
|
|
# ----- The default config with dynamic switching -----
|
|
-DHID_DYNAMIC
|
|
-DHID_WITH_USB
|
|
-DHID_SET_USB_KBD
|
|
-DHID_SET_USB_MOUSE_ABS
|
|
# ----- PS2 keyboard only -----
|
|
# -DHID_WITH_PS2
|
|
# -DHID_SET_PS2_KBD
|
|
# ----- PS2 keyboard + USB absolute mouse -----
|
|
# -DHID_WITH_USB
|
|
# -DHID_WITH_PS2
|
|
# -DHID_SET_PS2_KBD
|
|
# -DHID_SET_USB_MOUSE_ABS
|
|
# ----- PS2 keyboard + USB relative mouse -----
|
|
# -DHID_WITH_USB
|
|
# -DHID_WITH_PS2
|
|
# -DHID_SET_PS2_KBD
|
|
# -DHID_SET_USB_MOUSE_REL
|
|
```
|
|
|
|
By default, the firmware works with USB HID and supports dynamic mode switching. You can choose one of the other modes by commenting some lines and uncommenting others. This example to use a USB mouse and PS/2 keyboard:
|
|
```ini
|
|
...
|
|
# ----- The default config with dynamic switching -----
|
|
# -DHID_DYNAMIC
|
|
# -DHID_WITH_USB
|
|
# -DHID_SET_USB_KBD
|
|
# -DHID_SET_USB_MOUSE_ABS
|
|
# ----- PS2 keyboard only -----
|
|
...
|
|
# ----- PS2 keyboard + USB absolute mouse -----
|
|
-DHID_WITH_USB
|
|
-DHID_WITH_PS2
|
|
-DHID_SET_PS2_KBD
|
|
-DHID_SET_USB_MOUSE_ABS
|
|
# ----- PS2 keyboard + USB relative mouse -----
|
|
...
|
|
```
|
|
|
|
Next, you need to connect Arduino pins to the female PS/2 port of your motherboard. Choose the purple port. If your motherboard only have one port, it's probably universal and can be used either for the keyboard or for the mouse. Most likely, it is painted in two colors: green and purple. You can use it either.
|
|
|
|
Follow this diagram:
|
|
| Female PS/2 port (front view) | Pinout |
|
|
|-------------------------------|--------|
|
|
| <img src="https://raw.githubusercontent.com/pikvm/pikvm/master/img/ps2_kbd.png" alt="drawing" width="200"/> | Arduino pin 7 <-> PS/2 CLOCK<br>Arduino pin 5 <-> PS/2 DATA<br>Arduino GND pin <-> PS/2 GND |
|
|
|
|
**Connect VIN pin of Arduino to [any Raspberry's 5v pin](https://pinout.xyz/pinout/5v_power) for PS/2 only device. But you don't need to connect the Arduino VIN pin if you connected USB (Arduino will get power through it).**
|
|
|
|
## Fixing the USB absolute mouse on Windows 98
|
|
Due to an ancient buggy driver, the USB absolute mouse on Windows 98 moves only within the upper-left quarter of the screen. To fix this, you need to recompile the firmware with uncommented flag `-DHID_WITH_USB_WIN98` in `platformio.ini`.
|
|
|
|
## SPI connection to Arduino Micro
|
|
Using an SPI connection, an Arduino Micro or compatible can be flashed from the Pi and used as an HID keyboard and mouse. Unlike UART, SPI does not share pins with Bluetooth on the Raspberry Pi so the Bluetooth radio does not need to be disabled.
|
|
|
|
<img src="https://raw.githubusercontent.com/pikvm/pikvm/master/img/arduino_spi_hid.png" alt="Diagram of the Arduino SPI wiring for HID keyboard and mouse." width="654"/>
|
|
|
|
Before powering either device, double-check the connections. The following should be wired from the Pi to either the level shifter or the Arduino. While the Arduino tolerates 3.3V logic input, 5V outputs from the Arduino can damage or destroy the Raspberry Pi and must not be connected directly to 3.3V GPIO pins directly.
|
|
|
|
### Parts List
|
|
|
|
There are very few parts needed besides the Raspberry Pi to build the solution. Some parts may be purchased with or without headers, if headers are not pre-soldered, it may be necessary to order some breakaway header strips and solder them to the boards prior to assembly unless the wires will be soldered directly to the boards.
|
|
|
|
* Raspberry Pi Zero W or Pi 4 are the most popular boards for this solution, pre-soldered headers recommended
|
|
* Arduino Micro (or compatible) microcontroller board with pre-soldered headers recommended
|
|
* Logic Level Converter. This may be RX/TX, Bidirectional, or Single Supply
|
|
* Dupont wires (female to male pin) recommended for breadboard or other suitable means of making the connections
|
|
* ***Optional:*** Breakaway headers for the logic level converter
|
|
* ***Optional:*** Breadboard large enough to accomodate the parts
|
|
* ***Optional:*** Header pins for connection to a breadboard
|
|
|
|
***Note:*** A smaller "Pro Micro" board is available in a 3.3V model but the SS connection (RX_LED) is not available as a separate pin or solderable hole. If using this board, a jumper wire can be soldered to the resistor for the RX_LED but there is risk of burning the resistor, the LED, the board, or other components in the process. Advantages of this board include not requiring a logic level converter and reduced breadboard or board space for building the solution.
|
|
|
|
### List of connections to be made
|
|
|
|
For the primary functionality, most connections are made using a 4-channel bidirectional level shifter
|
|
* Pi 3v3 to LV on the level shifter
|
|
* Pi Ground to LV GND
|
|
* Arduino GND to HV GND
|
|
* GPIO10 (MOSI) via the level shifter to MOSI on the Arduino
|
|
* GPIO9 (MISO) via the level shifter to MISO on the Arduino
|
|
* GPIO11 (SPIO_SCLK) via the level shifter to SCK on the Arduino
|
|
* GPIO7 (SPIO_CE1_N) via the level shifter to SS (or RX_LED) on the Arduino
|
|
|
|
An additional circuit is used with a transistor to reset the HID for mode changes and for SPI programming as follows:
|
|
* GPIO25 to PNP base on transistor
|
|
* PNP emitter to ground
|
|
* PNP collector to RST on the Arduino
|
|
|
|
Pictures of this setup are also available in full resolution for download to assist for both the Raspberry Pi and the microcontroller board. A smaller version of the images has been included on this page and can be downloaded.
|
|
|
|
| Raspberry Pi Closeup | Breadboard with Arduino |
|
|
|------------|--------|
|
|
| <img src="https://raw.githubusercontent.com/pikvm/pikvm/master/img/arduino_spi_hid_rpi.jpg" alt="A closeup of the Raspberry Pi wired to the breadboard." width=300/> | <img src="https://raw.githubusercontent.com/pikvm/pikvm/master/img/arduino_spi_hid_bb.jpg" alt="Arduino on a breadboard fully wired to the Pi." width=300/> |
|
|
|
|
Programming assumes the Arduino is powered via USB, either from the connected host or the Pi itself. If the USB is not connected, 5 V may be provided by the Raspberry Pi GPIO but should be disconnected prior to connecting USB to the microcontroller's USB port. The Raspberry Pi does not have backcurrent protection, a circuit using one or more Schottky diodes can be built to OR power from multiple sources but it's easier and more cost effective to avoid conflict and voltage differences between power supplies by leaving the 5 V wire disconnected.
|
|
|
|
### Preparing the installation for SPI devices and programming
|
|
|
|
As of the latest package release, the kdmd service supports SPI. It should be sufficient to ensure the packages are up-to-date with the latest release, the programmer is installed, and the SPI device overlay is loaded at boot.
|
|
|
|
* Switch the filesystem to read-write mode with `rw`
|
|
* Update the system with `pacman -Syu` for the latest packages
|
|
* Install the avrdude programmer with `pacman -S avrdude-svn`
|
|
* Add `dtoverlay=spi0-1cs` to `/boot/config.txt`
|
|
* Reboot with `reboot` or `systemctl reboot`
|
|
|
|
### Flashing the Arduino microcontroller
|
|
|
|
Instructions on flashing the microcontroller can be found on the page [Flash the Arduino HID](flashing_hid.md).
|
|
|
|
If programming fails, ensure the Arduino is powered and check the wiring again. If there is a misconfiguration, power off the Pi and the Arduino, correct the wiring, and try again. Note it is not recommended or required to supply 5V power from the Raspberry Pi if the microcontroller is USB powered, if the issue appears to be power related it may be removed from the solution and replaced with a powered USB connection if it will aid in troubleshooting but check all other wires first to ensure there are no shorts.
|
|
|
|
Wiring problems are a common issue but there could be other reasons for programming not to complete. While it is not possible to list every possible problem and solution here, there is an active user community on Discord at https://discord.gg/bpmXfz5 with others familiar with the solution and willing to help.
|
|
|
|
### Enable the SPI configuration and restart kvmd
|
|
|
|
Once the installation has completed, all that should remain is to add the following configuration to `/etc/kvmd/override.yaml` and restart the kvmd service. If the first line exists due to existing overrides, omit that line and either add or update the hid section as appropriate.
|
|
```yaml
|
|
kvmd:
|
|
hid:
|
|
type: spi
|
|
chip: 0
|
|
bus: 0
|
|
sw_cs_pin: 7
|
|
reset_pin: 25
|
|
reset_inverted: true
|
|
```
|
|
|
|
After saving the changes to `/etc/kvmd/override.yaml`, restart `kvmd` and clear your browser cache. The command to restart `kvmd` is
|
|
|
|
```sh
|
|
systemctl restart kvmd
|
|
```
|
|
|
|
If your device is still in read-write mode, `ro` will put the SD back in read-only mode.
|